J'ai de la peine à configurer ma carte tv (Hauppauge Win/TV avec bt848). La mandrake 8.2 (kernel 2.4.18) me l'a reconnue mais n'arrive pas à me sortir du son. Sur le site de LEA, c'est marqué d'activer "Low level sound ..." dans le noyau et d'activer le msp3400. j'aimerais bien mais je ne trouve rien y correspondant...
 
ca serait sympa d'avoir un coup de pouce...(et soyez bien explicite, je débute...)  
 
merci !

tu as le modules msp3400 ?
 
tentes un "updatedb && locate msp3400.o"
 
ensuite "modprobe msd3400"
 
vais voir si j ai pas une doc la dessus.
 
Il me semble ke DS a exactement la meme carte et la meme distrib , il pourrait t aider au mieux je pense essaie de rajouter "Dark_Schneider" dans ton titre, si il voit il passera pour sûr je pense.
 
Regarde ca sinon : http://www.toolinux.com/linutile/p [...] usloin.htm

je comprends de moins en moins...
 
direct après l'install de linux, j'avais l'image sous xawtv (mais pas le son), je pouvais mater depuis ma video, mais maintenant, je n'ai plus rien du tout... scantv ne trouve rien. pourtant je n'ai pas l'impression d'avoir tellement tripatouillé de trucs...
 
je nage grave... need help please !!

il faut specifier les parametres qui vont bien pour le chargement du module du tuner et de bttv (dans /etc/modules.conf)
 
C'est tres bien expliqué dans la doc

fais voir ton /etc/modules.conf
 
tape dmesg et fais voir

Voici pour dmesg
*****************
 
Linux version 2.4.18-6mdk (quintela@bi.mandrakesoft.com) (gcc version 2.96 20000731 (Mandrake Linux 8.2 2.96-0.76mdk)) #1 Fri Mar 15 02:59:08 CET 2002
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000007ffc000 (usable)
 BIOS-e820: 0000000007ffc000 - 0000000007fff000 (ACPI data)
 BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
hm, page 07ffc000 reserved twice.
On node 0 totalpages: 32764
zone(0): 4096 pages.
zone(1): 28668 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=301 devfs=mount
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 350.799 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 126316k/131056k available (1170k kernel code, 4352k reserved, 332k data, 260k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0183fbff 00000000 00000000 00000000
CPU:             Common caps: 0183fbff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf08b0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
PCI: Found IRQ 9 for device 00:09.0
PCI: Sharing IRQ 9 with 00:04.2
PCI: Sharing IRQ 9 with 00:0d.0
PCI: Found IRQ 10 for device 00:0c.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: Card '3Com 3C509B EtherLink III'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 32049H2, ATA DISK drive
hdc: Pioneer DVD-ROM ATAPIModel DVD-103S 011, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 40021632 sectors (20491 MB) w/2048KiB Cache, CHS=2491/255/63, UDMA(33)
hdc: ATAPI DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
 /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Uncompressing..........done.
Freeing initrd memory: 231k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 9 for device 00:0d.0
PCI: Sharing IRQ 9 with 00:04.2
PCI: Sharing IRQ 9 with 00:09.0
sym.0.13.0: setting PCI_COMMAND_PARITY...
sym0: <815> rev 0x4 on pci bus 0 device 13 function 0 irq 9
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.17a
  Vendor: PIONEER   Model: CD-ROM DR-U16S    Rev: 1.01
  Type:   CD-ROM                             ANSI SCSI revision: 02
  Vendor: TEAC      Model: CD-R56S           Rev: 1.0F
  Type:   CD-ROM                             ANSI SCSI revision: 02
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 260k freed
Real Time Clock Driver v1.10e
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
Adding Swap: 248968k swap-space (priority -1)
Linux video capture interface: v1.00
i2c-core.o: i2c core module version 2.6.2 (20011118)
i2c-algo-bit.o: i2c bit algorithm module version 2.6.2 (20011118)
i2c-core.o: driver i2c TV tuner driver registered.
i2c-core.o: driver i2c msp3400 driver registered.
bttv: driver version 0.7.83 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge is Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge
bttv: Host bridge needs ETBF enabled.
bttv: Bt8xx card found (0).
PCI: Enabling device 00:09.0 (0004 -> 0006)
PCI: Found IRQ 9 for device 00:09.0
PCI: Sharing IRQ 9 with 00:04.2
PCI: Sharing IRQ 9 with 00:0d.0
bttv0: Bt848 (rev 18) at 00:09.0, irq: 9, latency: 32, memory: 0xe2000000
bttv0: using: BT848A( *** UNKNOWN/GENERIC **) [card=0,autodetected]
bttv0: enabling ETBF (430FX/VP3 compatibilty)
tuner: chip found @ 0xc2
bttv0: i2c attach [client=(unset),ok]
i2c-core.o: client [(unset)] registered to adapter [bt848 #0](pos. 0).
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_conntrack (1023 buckets, 8184 max)
ip_tables: (C) 2000-2002 Netfilter core team
8139too Fast Ethernet driver 0.9.24
PCI: Enabling device 00:0a.0 (0004 -> 0007)
PCI: Assigned IRQ 5 for device 00:0a.0
eth0: RealTek RTL8139 Fast Ethernet at 0xc88df000, 00:02:44:29:7f:95, IRQ 5
eth0:  Identified 8139 chip type 'RTL-8139C'
eth1: 3c5x9 at 0x220, 10baseT port, address  00 20 af c1 8a 64, IRQ 11.
3c509.c:1.18a 17Nov2001becker@scyld.com
http://www.scyld.com/network/3c509.html
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 03:23:39 Mar 15 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 9 for device 00:04.2
PCI: Sharing IRQ 9 with 00:09.0
PCI: Sharing IRQ 9 with 00:0d.0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x46d/0xc00b) is not claimed by any active driver.
hub.c: USB new device connect on bus1/2, assigned device number 3
usb.c: USB device 3 (vend/prod 0x7c4/0xa109) is not claimed by any active driver.
usb.c: registered new driver usb_mouse
input0: Logitech USB Mouse on usb1:2.0
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
  Vendor: Datafab   Model: USB to CF + SM C  Rev: 1708
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08  
Info fld=0x0, Current sd00:00: sense key None
sda : block size assumed to be 512 bytes, disk size 1GB.  
 /dev/scsi/host1/bus0/target0/lun0:SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 8000002
Info fld=0x0, Current sd08:00: sense key None
 I/O error: dev 08:00, sector 0
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 8000002
Info fld=0x0, Current sd08:00: sense key None
 I/O error: dev 08:00, sector 2
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 8000002
Info fld=0x0, Current sd08:00: sense key None
 I/O error: dev 08:00, sector 4
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 8000002
Info fld=0x0, Current sd08:00: sense key None
 I/O error: dev 08:00, sector 6
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 8000002
Info fld=0x0, Current sd08:00: sense key None
 I/O error: dev 08:00, sector 0
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 8000002
Info fld=0x0, Current sd08:00: sense key None
 I/O error: dev 08:00, sector 2
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 8000002
Info fld=0x0, Current sd08:00: sense key None
 I/O error: dev 08:00, sector 4
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 8000002
Info fld=0x0, Current sd08:00: sense key None
 I/O error: dev 08:00, sector 6
 unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
USB Mass Storage support registered.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
eth1: Setting Rx mode to 1 addresses.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: compatibility mode
Creative EMU10K1 PCI Audio Driver, version 0.18, 03:23:33 Mar 15 2002
PCI: Enabling device 00:0b.0 (0004 -> 0005)
PCI: Assigned IRQ 5 for device 00:0b.0
emu10k1: EMU10K1 rev 4 model 0x20 found, IO at 0xb800-0xb81f, IRQ 5
ac97_codec: AC97  codec, id: 0x5452:0x4103 (TriTech TR28023)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
[drm] AGP 0.99 on Intel 440BX @ 0xe4000000 64MB
[drm] Initialized mga 3.0.2 20010321 on minor 0
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 3, lun 0
sym0:2: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 8)
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
sym0:3: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 8)
sr1: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
 
 
 
et pour /etc/modules.conf
****************************
alias usb-interface usb-uhci  
alias sound-slot-0 emu10k1  
probeall scsi_hostadapter sym53c8xx  
alias eth0 8139too  
alias eth1 3c509  
alias char-major-81 bttv
pre-install bttv modprobe -k tuner; modprobe -k msp3400  
alias tvcard0 bttv
 
 
 
(A noter que je ne suis pas sur d'avoir le msp3400, mais LEA dit que avec les tuner philips ca devrait etre ca... sinon je ne sais pas comment faire pour savoir, et y a rien de marqué sur les chips de ma carte...)

ok je sais résoudre le problème mais la je suis un peu fatigué , je mets la solution demain

up...

Mon dieu.... tu fais appelle a Dark Schneider, le demon majeur de l'ancien temps...mais tu es fou(olle) ...
Considerer cela comme un UP, ca m'intesse !

bon j'ai ta solution

bon pour ton /etc/modules.conf pour bttv il faut juste mettre :
 
alias char-major-81 bttv
options bttv card=1 radio=0
 
card=1 correspond a ma miropctv mais pour ta carte je crois que c'est card=2
 
D'après ton dmesg ta carte n'est détecté avec juste les deux lignes que je t'ai donné ca devrait allé car j'avais le meme problème que toi

[will@bastard will]$ dmesg | grep bttv
bttv: driver version 0.7.83 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge is VIA Technologies, Inc. VT8371 [KX133]
bttv: Host bridge is VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 00:0d.0, irq: 5, latency: 32, memory: 0xd6800000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: BT878(Hauppauge (bt878)) [card=10,autodetected]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
bttv0: Hauppauge eeprom: model=61326, tuner=Philips FI1216MF MK2 (3), radio=no
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c attach [client=MSP3415D-B3,ok]
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c attach [client=Philips SECAM,ok]
bttv0: PLL: 28636363 => 35468950 ... ok
 
 
 
[will@bastard will]$ more /etc/modules.conf
 
alias usb-interface usb-uhci
alias sound-slot-0 emu10k1
probeall scsi_hostadapter aic7xxx
alias eth0 tulip
#alias eth1 tulip
alias char-major-81 bttv
alias /dev/nvidia*   NVdriver
 
 
 
[will@bastard will]$ /sbin/lsmod | grep bttv
bttv                   59776   1
i2c-algo-bit            7244   1 [bttv]
i2c-core               13568   0 [tuner tvaudio msp3400 bttv i2c-algo-bit]
videodev                4896   3 [bttv]

je remarque que :
 
+ ta carte partage son IRQ avec 3 autres trucs
=> mets dans le BIOS : PnP OS = No
 
+ donne l'occupation de tes slots PCI, tu devrais peut être déplacé ta carte TV pour que celle-ci soit tranquille car cela semble géner la détection
 
+ n'oublie pas dans xawtv de préciser l'entrée sur laquelle est branchée la carte TV ( le petit cordon jack qui relie la carte TV à la carte son ).
 

Tiens j'avais pas fait attention à l'irq
Avec tous nos conseils il devrait s'en tirer non ?