Bringing up eth0

Bringing up eth0 - Linux et OS Alternatifs

Marsh Posté le 11-05-2002 à 19:56:21    

je suis en train d'essayer de me faire un routeur internet avec un vieux celeron 400 mais j'ai que des problemes.
 
Au boot , il plante tjs sur bringing up eth0 et ca dure vachement longtemps avant.
 
J'arrive pas a router...
 
je peux pas mettre autre chose que redhat 7.1 , mon modem a un driver qui ne marche qu'avec celle la.
 
Si vous pouviez m'aider(surtout pour eth0 , c'est important quand meme)

Reply

Marsh Posté le 11-05-2002 à 19:56:21   

Reply

Marsh Posté le 11-05-2002 à 19:58:27    

quand tu tapes ifup eth0 , il te répond quoi ?


---------------
Celui qui pose une question est idiot 5 minutes. Celui qui n'en pose pas le reste toute sa vie. |  Membre du grand complot pharmaceutico-médico-scientifico-judéo-maçonnique.
Reply

Marsh Posté le 11-05-2002 à 20:00:16    

il doit chercher un serveur DHCP
regarde dans /etc/config/netwark/eth0


---------------
Jyp
Reply

Marsh Posté le 11-05-2002 à 20:02:51    

si je fais ifconfig 192.168.0.1 netmask 255.255.255.0 apres ca marche mais au demarrage je sais pas trop ce qu'il fait .
 
qu'est ce que je dois cherher dans /etc/config/netwark/eth0  ????

 

[jfdsdjhfuetppo]--Message édité par Asarnil le 11-05-2002 à 20:03:15--[/jfdsdjhfuetppo]

Reply

Marsh Posté le 11-05-2002 à 20:08:09    

Asarnil a écrit a écrit :

si je fais ifconfig 192.168.0.1 netmask 255.255.255.0 apres ca marche mais au demarrage je sais pas trop ce qu'il fait .
 
qu'est ce que je dois cherher dans /etc/config/netwark/eth0  ????  
 
 




/etc/config/network/eth0  C seulement dans certaine distrib.
il faut que t'automatise ton ifconfig.
faut un script et met le dans /etc/rc.d
apres tu fait un lien dans le niveau de demarrage auquel tu demmare a chaque fois:
ln -s /etc/rc.d/mon_script /etc/rc.d/rc5/S00monscrip

Reply

Marsh Posté le 11-05-2002 à 20:43:23    

now , c'est samba qui marche po ....
 
je partage , quand je fais smbclient -L //192.168.0.1
 
je vois ce que je partage et je peux le mounter mais les clients windaube de mon reseau ne le voie pas alosr que je sais pinger.
 
Comprends po  :sweat:

Reply

Marsh Posté le 11-05-2002 à 20:49:27    

tiens non , ca marche mem plus quand je fais smbclient  :(
 

Citation :


[root@serveur samba]# smbclient -L //192.168.0.1
added interface ip=192.168.0.1 bcast=192.168.0.255 nmask=255.255.255.0
session request to 192.168.0.1 failed (code 0)
session request to 192 failed (code 0)
session request to *SMBSERVER failed (code 0)


 

Citation :


[root@serveur samba]# ifconfig
eth0      Lien encap:Ethernet  HWaddr 00:40:F4:39:33:0D
          inet adr:192.168.0.1  Bcast:192.168.0.255  Masque:255.255.255.0
          UP BROADCAST RUNNING  MTU:1500  Metric:1
          Paquets Reçus:2925 erreurs:0 jetés:0 débordements:0 trames:0
          Paquets transmis:2228 erreurs:0 jetés:0 débordements:0 carrier:0
          collisions:0 lg file transmission:100
          Interruption:5 Adresse de base:0x8000
 
lo        Lien encap:Boucle locale
          inet adr:127.0.0.1  Masque:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          Paquets Reçus:441 erreurs:0 jetés:0 débordements:0 trames:0
          Paquets transmis:441 erreurs:0 jetés:0 débordements:0 carrier:0
          collisions:0 lg file transmission:0
 


 

Citation :


[global]
 
# workgroup = NT-Domain-Name or Workgroup-Name
   workgroup = LAN
 
# server string is the equivalent of the NT Description field
   server string = Samba Server
 
# This option is important for security. It allows you to restrict
# connections to machines which are on your local network. The
# following example restricts access to two C class networks and
# the "loopback" interface. For more examples of the syntax see
# the smb.conf man page
;   hosts allow = 192.168.0. 127.
 
# if you want to automatically load your printer list rather
# than setting them up individually then you'll need this
   printcap name = /etc/printcap
   load printers = yes
 
# It should not be necessary to spell out the print system type unless
# yours is non-standard. Currently supported print systems include:
# bsd, sysv, plp, lprng, aix, hpux, qnx
   printing = lprng
 
# Uncomment this if you want a guest account, you must add this to /etc/passwd
# otherwise the user "nobody" is used
;  guest account = pcguest
 
# this tells Samba to use a separate log file for each machine
# that connects
   log file = /var/log/samba/%m.log
 
# Put a capping on the size of the log files (in Kb).
   max log size = 0
 
# Security mode. Most people will want user level security. See
# security_level.txt for details.
   security = share
# Use password server option only with security = server or
# security = domain
;   password server = <NT-Server-Name>
 
# Password Level allows matching of _n_ characters of the password for
# all combinations of upper and lower case.
;  password level = 8
;  username level = 8
 
# You may wish to use password encryption. Please read
# ENCRYPTION.txt, Win95.txt and WinNT.txt in the Samba documentation.
# Do not enable this option unless you have read those documents
;  encrypt passwords = yes
;  smb passwd file = /etc/samba/smbpasswd
 
# The following is needed to keep smbclient from spouting spurious errors
# when Samba is built with support for SSL.
   ssl CA certFile = /usr/share/ssl/certs/ca-bundle.crt
 
# The following are needed to allow password changing from Windows to
# update the Linux sytsem password also.
# NOTE: Use these with 'encrypt passwords' and 'smb passwd file' above.
# NOTE2: You do NOT need these to allow workstations to change only
#        the encrypted SMB passwords. They allow the Unix password
#        to be kept in sync with the SMB password.
;  unix password sync = Yes
;  passwd program = /usr/bin/passwd %u
;  passwd chat = *New*UNIX*password* %n\n *ReType*new*UNIX*password* %n\n *passwd:*all*authentication*tokens*updated*successfully*
 
# Unix users can map to different SMB User names
;  username map = /etc/samba/smbusers
 
# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /etc/samba/smb.conf.%m
 
# Most people will find that this option gives better performance.
# See speed.txt and the manual pages for details
   socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192
 
# Configure Samba to use multiple interfaces
# If you have multiple network interfaces then you must list them
# here. See the man page for details.
;   interfaces = 192.168.12.2/24 192.168.13.2/24
 
# Configure remote browse list synchronisation here
#  request announcement to, or browse list sync from:
#       a specific host or from / to a whole subnet (see below)
;   remote browse sync = 192.168.3.25 192.168.5.255
# Cause this host to announce itself to local subnets here
;   remote announce = 192.168.1.255 192.168.2.44
 
# Browser Control Options:
# set local master to no if you don't want Samba to become a master
# browser on your network. Otherwise the normal election rules apply
;   local master = no
 
# OS Level determines the precedence of this server in master browser
 
# OS Level determines the precedence of this server in master browser
# elections. The default value should be reasonable
;   os level = 33
 
# Domain Master specifies Samba to be the Domain Master Browser. This
# allows Samba to collate browse lists between subnets. Don't use this
# if you already have a Windows NT domain controller doing this job
;   domain master = yes
 
# Preferred Master causes Samba to force a local browser election on startup
# and gives it a slightly higher chance of winning the election
;   preferred master = yes
 
# Enable this if you want Samba to be a domain logon server for
# Windows95 workstations.
;   domain logons = yes
 
# if you enable domain logons then you may want a per-machine or
# per user logon script
# run a specific logon batch file per workstation (machine)
;   logon script = %m.bat
# run a specific logon batch file per username
;   logon script = %U.bat
 
# All NetBIOS names must be resolved to IP Addresses
# 'Name Resolve Order' allows the named resolution mechanism to be specified
# the default order is "host lmhosts wins bcast". "host" means use the unix
# system gethostbyname() function call that will use either /etc/hosts OR
# DNS or NIS depending on the settings of /etc/host.config, /etc/nsswitch.conf
# and the /etc/resolv.conf file. "host" therefore is system configuration
# dependant. This parameter is most often of use to prevent DNS lookups
# in order to resolve NetBIOS names to IP Addresses. Use with care!
# The example below excludes use of name resolution for machines that are NOT
# on the local network segment
# - OR - are not deliberately to be known via lmhosts or via WINS.
; name resolve order = wins lmhosts bcast
 
# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable it's WINS Server
;   wins support = yes
 
# WINS Server - Tells the NMBD components of Samba to be a WINS Client
#       Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z
 
# WINS Proxy - Tells Samba to answer name resolution queries on
# behalf of a non WINS capable client, for this to work there must be
# at least one  WINS Server on the network. The default is NO.
;   wins proxy = yes
 
# DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names
# via DNS nslookups. The built-in default for versions 1.9.17 is yes,
# this has been changed in version 1.9.18 to no.
   dns proxy = no
 
# Case Preservation can be handy - system default is _no_
# NOTE: These can be set on a per share basis
;  preserve case = no
;  short preserve case = no
# Default case is normally upper case for all DOS files
;  default case = lower
# Be very careful with case sensitivity - it can break things!
;  case sensitive = no
 
#============================ Share Definitions ==============================
[homes]
   comment = Home Directories
   browseable = no
   writable = yes
 
# Un-comment the following and create the netlogon directory for Domain Logons
; [netlogon]
;   comment = Network Logon Service
;   path = /home/netlogon
;   guest ok = yes
;   writable = no
;   share modes = no
 
 
# Un-comment the following to provide a specific roving profile share
# the default is to use the user's home directory
;[Profiles]
;    path = /home/profiles
;    browseable = no
;    guest ok = yes
 
 
# NOTE: If you have a BSD-style print system there is no need to
# specifically define each individual printer
[printers]
   comment = All Printers
   path = /var/spool/samba
   browseable = no
# Set public = yes to allow user 'guest account' to print
   guest ok = no
   printable = yes
 
# This one is useful for people to share files
;[tmp]
;   comment = Temporary file space
;   path = /tmp
;   read only = no
;   public = yes
 
# A publicly accessible directory, but read only, except for people in
# the "staff" group
;[public]
;   comment = Public Stuff
;   path = /home/samba
;   public = yes
;   writable = yes
;   printable = no
;   write list = @staff
 
# Other examples.
#
# A private printer, usable only by fred. Spool data will be placed in fred's
# home directory. Note that fred must have write access to the spool directory,
# wherever it is.
;[fredsprn]
;   comment = Fred's Printer
;   valid users = fred
;   path = /homes/fred
;   printer = freds_printer
;   public = no
;   printable = yes
 
# A private directory, usable only by fred. Note that fred requires write
# access to the directory.
;[fredsdir]
;   comment = Fred's Service
;   path = /usr/somewhere/private
;   valid users = fred
;   public = no
;   writable = yes
;   printable = no
 
# a service which has a different directory for each machine that connects
# this allows you to tailor configurations to incoming machines. You could
# also use the %u option to tailor it by user name.
# The %m gets replaced with the machine name that is connecting.
;[pchome]
;  comment = PC Directories
;  path = /usr/pc/%m
;  public = no
;  writable = yes
 
# A publicly accessible directory, read/write to all users. Note that all files
# created in the directory by users will be owned by the default user, so
# any user with access can delete any other user's files. Obviously this
# directory must be writable by the default user. Another user could of course
# be specified, in which case all files would be owned by that user instead.
;[public]
;   path = /usr/somewhere/else/public
;   public = yes
;   only guest = yes
;   writable = yes
;   printable = no
 
# The following two entries demonstrate how to share a directory so that two
# users can place files there that will be owned by the specific users. In this
# setup, the directory should be writable by both users and should have the
# sticky bit set on it to prevent abuse. Obviously this could be extended to
# as many users as required.
 
;[myshare]
;   comment = Mary's and Fred's stuff
;   path = /usr/somewhere/shared
;   valid users = mary fred
;   public = no
;   writable = yes
;   printable = no
;   create mask = 0765
[serveur]
        comment = serveur ressources
        path = /home/asarnil/
        public = yes
        writable = yes
        browseable = yes
        create mask = 0765

 

[jfdsdjhfuetppo]--Message édité par Asarnil le 11-05-2002 à 21:09:50--[/jfdsdjhfuetppo]

Reply

Marsh Posté le 11-05-2002 à 21:07:29    

Asarnil a écrit a écrit :

si je fais ifconfig 192.168.0.1 netmask 255.255.255.0 apres ca marche mais au demarrage je sais pas trop ce qu'il fait .
 
qu'est ce que je dois cherher dans /etc/config/netwark/eth0  ????  
 
 




si tu en as un, il y a quoi dedans?


---------------
Jyp
Reply

Marsh Posté le 11-05-2002 à 21:11:34    

j'en ai pas , je suis vraiment paume la . c'est vachement complique de faire un serveur linux sans X , je croiais pas autant :sweat: .

Reply

Marsh Posté le 11-05-2002 à 21:15:18    

tu n'as pas un fichier : eth0
find /etc -iname eth0

 

[jfdsdjhfuetppo]--Message édité par jyp le 11-05-2002 à 21:17:01--[/jfdsdjhfuetppo]


---------------
Jyp
Reply

Marsh Posté le 11-05-2002 à 21:15:18   

Reply

Marsh Posté le 11-05-2002 à 21:20:44    

non plus

Reply

Marsh Posté le 11-05-2002 à 21:29:31    

et /etc/sysconfig/network-scripts/ifcfg-eth0 ?

Reply

Marsh Posté le 11-05-2002 à 21:38:42    

j'ai l'arborescence jusque la mais pas le fichier.
 
Vous n'auriez pas une idee pour samba , ca fait un bout de tps que je rame dessus la.

Reply

Marsh Posté le 11-05-2002 à 22:18:53    

up avant la nuit

Reply

Marsh Posté le 12-05-2002 à 14:15:12    

:bounce:

Reply

Sujets relatifs:

Leave a Replay

Make sure you enter the(*)required information where indicate.HTML code is not allowed