Demande avis sur état SMART - Disque dur - Hardware
MarshPosté le 10-11-2014 à 12:43:29
Bonjour
J'ai un NAS (HP Proliant N40L) avec 4 disques de 2To chacun en RAID5 de chez Western Digital (les modèle RED). Sur le disque systeme est installé Open Media Vault
Depuis hier matin, je reçois cette alerte sur 3 de mes 4 disques
Device: /dev/disk/by-id/wwn-0x50014ee0ae59a87f [SAT], ATA error count increased from 0 to 1
Voici les infos SMART de chaque disque :
Disque 1
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION === Device Model: WDC WD20EFRX-68AX9N0 Serial Number: WD-WMC300060002 Firmware Version: 80.00A80 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Nov 9 12:36:46 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED
General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 248) Self-test routine in progress... 80% of test remaining. Total time to complete Offline data collection: (26280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
General Purpose Logging (GPL) feature set supported General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 4959 hours (206 days + 15 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 5903 Vendor specific
Disque 2
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION === Device Model: WDC WD20EFRX-68AX9N0 Serial Number: WD-WMC300014205 Firmware Version: 80.00A80 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Nov 9 12:37:11 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED
General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (27120) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
General Purpose Logging (GPL) feature set supported General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 4772 hours (198 days + 20 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4772 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 22/31 Celsius Lifetime Min/Max Temperature: 17/36 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (436)
SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 5928 Vendor specific
Disque 3
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION === Device Model: WDC WD20EFRX-68EUZN0 Serial Number: WD-WMC4M1620040 Firmware Version: 80.00A80 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Nov 9 12:37:19 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED
General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (27120) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
General Purpose Logging (GPL) feature set supported General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 2207 - # 2 Short offline Aborted by host 60% 2207 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 22/31 Celsius Lifetime Min/Max Temperature: 19/36 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (214)
SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 5935 Vendor specific
Disque 4
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION === Device Model: WDC WD20EFRX-68EUZN0 Serial Number: WD-WMC4M1433716 Firmware Version: 80.00A80 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Nov 9 12:37:27 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED
General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 248) Self-test routine in progress... 80% of test remaining. Total time to complete Offline data collection: (26160) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
General Purpose Logging (GPL) feature set supported General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 93 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 2206 hours (91 days + 22 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Marsh Posté le 10-11-2014 à 12:43:29
Bonjour
J'ai un NAS (HP Proliant N40L) avec 4 disques de 2To chacun en RAID5 de chez Western Digital (les modèle RED).
Sur le disque systeme est installé Open Media Vault
Depuis hier matin, je reçois cette alerte sur 3 de mes 4 disques
Device: /dev/disk/by-id/wwn-0x50014ee0ae59a87f [SAT], ATA error count increased from 0 to 1
Voici les infos SMART de chaque disque :
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EFRX-68AX9N0
Serial Number: WD-WMC300060002
Firmware Version: 80.00A80
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Nov 9 12:36:46 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 248) Self-test routine in progress...
80% of test remaining.
Total time to complete Offline
data collection: (26280) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 173 170 021 Pre-fail Always - 4333
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 660
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 4960
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 650
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 385
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 274
194 Temperature_Celsius 0x0022 116 112 000 Old_age Always - 31
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
General Purpose Logging (GPL) feature set supported
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaa has 1 sectors [Device vendor specific log]
GP/S Log at address 0xab has 1 sectors [Device vendor specific log]
GP/S Log at address 0xac has 1 sectors [Device vendor specific log]
GP/S Log at address 0xad has 1 sectors [Device vendor specific log]
GP/S Log at address 0xae has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaf has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xbd has 1 sectors [Device vendor specific log]
GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log]
GP Log at address 0xc1 has 93 sectors [Device vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 1
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 4959 hours (206 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:39:57.601 SMART READ LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:39:57.600 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:39:57.600 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:39:57.600 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:39:57.599 SMART READ LOG
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 90% 4959 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: DST executing in background (3)
Current Temperature: 31 Celsius
Power Cycle Min/Max Temperature: 21/31 Celsius
Lifetime Min/Max Temperature: 16/35 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (242)
Index Estimated Time Temperature Celsius
243 2014-11-09 04:39 28 *********
... ..( 99 skipped). .. *********
343 2014-11-09 06:19 28 *********
344 2014-11-09 06:20 ? -
345 2014-11-09 06:21 21 **
346 2014-11-09 06:22 22 ***
347 2014-11-09 06:23 22 ***
348 2014-11-09 06:24 23 ****
... ..( 3 skipped). .. ****
352 2014-11-09 06:28 23 ****
353 2014-11-09 06:29 24 *****
354 2014-11-09 06:30 24 *****
355 2014-11-09 06:31 24 *****
356 2014-11-09 06:32 25 ******
... ..( 2 skipped). .. ******
359 2014-11-09 06:35 25 ******
360 2014-11-09 06:36 26 *******
... ..( 8 skipped). .. *******
369 2014-11-09 06:45 26 *******
370 2014-11-09 06:46 27 ********
... ..( 15 skipped). .. ********
386 2014-11-09 07:02 27 ********
387 2014-11-09 07:03 28 *********
388 2014-11-09 07:04 28 *********
389 2014-11-09 07:05 28 *********
390 2014-11-09 07:06 29 **********
... ..( 4 skipped). .. **********
395 2014-11-09 07:11 29 **********
396 2014-11-09 07:12 30 ***********
... ..( 19 skipped). .. ***********
416 2014-11-09 07:32 30 ***********
417 2014-11-09 07:33 31 ************
... ..( 24 skipped). .. ************
442 2014-11-09 07:58 31 ************
443 2014-11-09 07:59 29 **********
... ..( 6 skipped). .. **********
450 2014-11-09 08:06 29 **********
451 2014-11-09 08:07 30 ***********
... ..( 54 skipped). .. ***********
28 2014-11-09 09:02 30 ***********
29 2014-11-09 09:03 29 **********
... ..( 41 skipped). .. **********
71 2014-11-09 09:45 29 **********
72 2014-11-09 09:46 30 ***********
... ..( 28 skipped). .. ***********
101 2014-11-09 10:15 30 ***********
102 2014-11-09 10:16 29 **********
... ..(101 skipped). .. **********
204 2014-11-09 11:58 29 **********
205 2014-11-09 11:59 28 *********
... ..( 36 skipped). .. *********
242 2014-11-09 12:36 28 *********
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 4 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 5903 Vendor specific
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EFRX-68AX9N0
Serial Number: WD-WMC300014205
Firmware Version: 80.00A80
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Nov 9 12:37:11 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (27120) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1
3 Spin_Up_Time 0x0027 173 171 021 Pre-fail Always - 4350
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 609
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 4773
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 600
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 340
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 268
194 Temperature_Celsius 0x0022 116 111 000 Old_age Always - 31
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
General Purpose Logging (GPL) feature set supported
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaa has 1 sectors [Device vendor specific log]
GP/S Log at address 0xab has 1 sectors [Device vendor specific log]
GP/S Log at address 0xac has 1 sectors [Device vendor specific log]
GP/S Log at address 0xad has 1 sectors [Device vendor specific log]
GP/S Log at address 0xae has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaf has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xbd has 1 sectors [Device vendor specific log]
GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log]
GP Log at address 0xc1 has 93 sectors [Device vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 1
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 4772 hours (198 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:42:49.456 SMART READ LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:42:49.456 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:42:49.455 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:42:49.454 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:42:49.454 SMART READ LOG
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4772 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 31 Celsius
Power Cycle Min/Max Temperature: 22/31 Celsius
Lifetime Min/Max Temperature: 17/36 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (436)
Index Estimated Time Temperature Celsius
437 2014-11-09 04:40 30 ***********
... ..( 79 skipped). .. ***********
39 2014-11-09 06:00 30 ***********
40 2014-11-09 06:01 29 **********
... ..( 17 skipped). .. **********
58 2014-11-09 06:19 29 **********
59 2014-11-09 06:20 ? -
60 2014-11-09 06:21 22 ***
61 2014-11-09 06:22 22 ***
62 2014-11-09 06:23 23 ****
63 2014-11-09 06:24 23 ****
64 2014-11-09 06:25 24 *****
... ..( 2 skipped). .. *****
67 2014-11-09 06:28 24 *****
68 2014-11-09 06:29 25 ******
69 2014-11-09 06:30 25 ******
70 2014-11-09 06:31 25 ******
71 2014-11-09 06:32 26 *******
72 2014-11-09 06:33 26 *******
73 2014-11-09 06:34 26 *******
74 2014-11-09 06:35 27 ********
... ..( 7 skipped). .. ********
82 2014-11-09 06:43 27 ********
83 2014-11-09 06:44 28 *********
... ..( 15 skipped). .. *********
99 2014-11-09 07:00 28 *********
100 2014-11-09 07:01 29 **********
... ..( 9 skipped). .. **********
110 2014-11-09 07:11 29 **********
111 2014-11-09 07:12 30 ***********
... ..( 18 skipped). .. ***********
130 2014-11-09 07:31 30 ***********
131 2014-11-09 07:32 31 ************
... ..(199 skipped). .. ************
331 2014-11-09 10:52 31 ************
332 2014-11-09 10:53 30 ***********
... ..(103 skipped). .. ***********
436 2014-11-09 12:37 30 ***********
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 4 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 5928 Vendor specific
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WMC4M1620040
Firmware Version: 80.00A80
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Nov 9 12:37:19 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (27120) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 174 172 021 Pre-fail Always - 4291
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 258
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2208
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 258
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 5
193 Load_Cycle_Count 0x0032 196 196 000 Old_age Always - 14503
194 Temperature_Celsius 0x0022 116 111 000 Old_age Always - 31
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
General Purpose Logging (GPL) feature set supported
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaa has 1 sectors [Device vendor specific log]
GP/S Log at address 0xab has 1 sectors [Device vendor specific log]
GP/S Log at address 0xac has 1 sectors [Device vendor specific log]
GP/S Log at address 0xad has 1 sectors [Device vendor specific log]
GP/S Log at address 0xae has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaf has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xbd has 1 sectors [Device vendor specific log]
GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log]
GP Log at address 0xc1 has 93 sectors [Device vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 2207 -
# 2 Short offline Aborted by host 60% 2207 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 31 Celsius
Power Cycle Min/Max Temperature: 22/31 Celsius
Lifetime Min/Max Temperature: 19/36 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (214)
Index Estimated Time Temperature Celsius
215 2014-11-09 04:40 ? -
216 2014-11-09 04:41 22 ***
217 2014-11-09 04:42 22 ***
218 2014-11-09 04:43 22 ***
219 2014-11-09 04:44 23 ****
220 2014-11-09 04:45 23 ****
221 2014-11-09 04:46 23 ****
222 2014-11-09 04:47 24 *****
... ..( 3 skipped). .. *****
226 2014-11-09 04:51 24 *****
227 2014-11-09 04:52 25 ******
228 2014-11-09 04:53 25 ******
229 2014-11-09 04:54 25 ******
230 2014-11-09 04:55 26 *******
231 2014-11-09 04:56 26 *******
232 2014-11-09 04:57 26 *******
233 2014-11-09 04:58 27 ********
... ..( 9 skipped). .. ********
243 2014-11-09 05:08 27 ********
244 2014-11-09 05:09 28 *********
... ..( 11 skipped). .. *********
256 2014-11-09 05:21 28 *********
257 2014-11-09 05:22 29 **********
... ..( 23 skipped). .. **********
281 2014-11-09 05:46 29 **********
282 2014-11-09 05:47 30 ***********
... ..( 19 skipped). .. ***********
302 2014-11-09 06:07 30 ***********
303 2014-11-09 06:08 31 ************
... ..( 10 skipped). .. ************
314 2014-11-09 06:19 31 ************
315 2014-11-09 06:20 30 ***********
... ..( 7 skipped). .. ***********
323 2014-11-09 06:28 30 ***********
324 2014-11-09 06:29 31 ************
... ..( 49 skipped). .. ************
374 2014-11-09 07:19 31 ************
375 2014-11-09 07:20 30 ***********
... ..( 46 skipped). .. ***********
422 2014-11-09 08:07 30 ***********
423 2014-11-09 08:08 31 ************
... ..( 40 skipped). .. ************
464 2014-11-09 08:49 31 ************
465 2014-11-09 08:50 30 ***********
... ..( 84 skipped). .. ***********
72 2014-11-09 10:15 30 ***********
73 2014-11-09 10:16 29 **********
... ..(140 skipped). .. **********
214 2014-11-09 12:37 29 **********
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 4 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 5935 Vendor specific
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WMC4M1433716
Firmware Version: 80.00A80
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Nov 9 12:37:27 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 248) Self-test routine in progress...
80% of test remaining.
Total time to complete Offline
data collection: (26160) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 173 172 021 Pre-fail Always - 4325
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 258
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2208
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 258
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 5
193 Load_Cycle_Count 0x0032 196 196 000 Old_age Always - 14540
194 Temperature_Celsius 0x0022 115 112 000 Old_age Always - 32
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
General Purpose Logging (GPL) feature set supported
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaa has 1 sectors [Device vendor specific log]
GP/S Log at address 0xab has 1 sectors [Device vendor specific log]
GP/S Log at address 0xac has 1 sectors [Device vendor specific log]
GP/S Log at address 0xad has 1 sectors [Device vendor specific log]
GP/S Log at address 0xae has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaf has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xbd has 1 sectors [Device vendor specific log]
GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log]
GP Log at address 0xc1 has 93 sectors [Device vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 1
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 2206 hours (91 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 00 08 00:30:40.825 SMART READ LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:30:40.825 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:30:40.824 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:30:40.824 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 00 08 00:30:40.823 SMART READ LOG
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 90% 2207 -
# 2 Extended offline Aborted by host 90% 2207 -
# 3 Extended offline Aborted by host 90% 2207 -
# 4 Short offline Completed without error 00% 2206 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: DST executing in background (3)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: 22/32 Celsius
Lifetime Min/Max Temperature: 18/35 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (206)
Index Estimated Time Temperature Celsius
207 2014-11-09 04:40 ? -
208 2014-11-09 04:41 22 ***
... ..( 3 skipped). .. ***
212 2014-11-09 04:45 22 ***
213 2014-11-09 04:46 23 ****
214 2014-11-09 04:47 24 *****
... ..( 4 skipped). .. *****
219 2014-11-09 04:52 24 *****
220 2014-11-09 04:53 25 ******
221 2014-11-09 04:54 26 *******
... ..( 2 skipped). .. *******
224 2014-11-09 04:57 26 *******
225 2014-11-09 04:58 27 ********
... ..( 10 skipped). .. ********
236 2014-11-09 05:09 27 ********
237 2014-11-09 05:10 28 *********
... ..( 7 skipped). .. *********
245 2014-11-09 05:18 28 *********
246 2014-11-09 05:19 29 **********
... ..( 4 skipped). .. **********
251 2014-11-09 05:24 29 **********
252 2014-11-09 05:25 30 ***********
... ..( 6 skipped). .. ***********
259 2014-11-09 05:32 30 ***********
260 2014-11-09 05:33 31 ************
... ..( 27 skipped). .. ************
288 2014-11-09 06:01 31 ************
289 2014-11-09 06:02 32 *************
... ..( 16 skipped). .. *************
306 2014-11-09 06:19 32 *************
307 2014-11-09 06:20 30 ***********
... ..( 15 skipped). .. ***********
323 2014-11-09 06:36 30 ***********
324 2014-11-09 06:37 31 ************
... ..( 17 skipped). .. ************
342 2014-11-09 06:55 31 ************
343 2014-11-09 06:56 30 ***********
... ..(147 skipped). .. ***********
13 2014-11-09 09:24 30 ***********
14 2014-11-09 09:25 29 **********
... ..(191 skipped). .. **********
206 2014-11-09 12:37 29 **********
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 4 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 5943 Vendor specific
Apparemment, seul le disque 3 n'a pas d'erreur mais au démarrage du système, j'ai eu le message suivant :
failed to enable aa (error_mask=0x1)
J'ai commencé a réaliser des tests (Long Self-Test) sur les 2 premiers disques.
Resultat : Aucune erreur sur ces 2 disques.
Est-ce qu'une âme charitable pourrait m'aider à et me dire si mes 3 (ou 4
Merci pour votre aide